Nп/п : 27 из 100
 От   : Snag                                2:5075/128        27 сен 23 12:14:16
 К    : Snag                                                  27 сен 23 20:16:02
 Тема : Re: Oldies but goodies Re: deburring inside drilled tubing?
----------------------------------------------------------------------------------
                                                                                 
@MSGID: 1@dont-email.me> 857241cb
@REPLY: 1@dont-email.me> 60107445
@REPLYADDR Snag <Snag_one@msn.com>
@REPLYTO 2:5075/128 Snag
@CHRS: CP866 2
@RFC: 1 0
@RFC-Message-ID: 1@dont-email.me>
@RFC-References:
<6hxId.68354$w62.50324@bgtnsc05-news.ops.worldnet.att.net> <980b04a9-30ff-44dc-9254-b2da270b2e43n@googlegroups.com>
<tc06hippbmpegm6oniu4sjo55b54mbrg39@4ax.com> <874jjgbsly.fsf@enoch.nodomain.nowhere> 1@dont-email.me>
1@dont-email.me>
@TZUTC: -0500
@PID: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:60.0)
Gecko/20100101 Thunderbird/60.6.1
@TID: FIDOGATE-5.12-ge4e8b94
On 9/27/2023 11:59 AM, Snag wrote:
> On 9/27/2023 11:27 AM, Jim Wilkins wrote:
>> "Mike Spencer"  wrote in message 
>> news:874jjgbsly.fsf@enoch.nodomain.nowhere...
>> pyotr filipivich <phamp@mindspring.com> writes:
>>
>>> Granted a little late, but something modeled on a brake cylinder
>>> hone might work
>>
>> I duct-tape one end of a strip of abrasive cloth to a piece of dowel,
>> wrap the strip around the dowel a few turns in the correct direction
>> and put the dowel in an electric drill or drill press.  Insert dowel
>> in tube and run the drill. Grit of abrasive and size of dowel
>> obviously to be chosen to suit requirements.
>>
>> Perhaps unsuitable for production work but it serves me fine for
>> various one-offs.
>>
>> Mike Spencer                  Nova Scotia, Canada
>>
>> -------------------------------
>>
>> I thought about and may have tried winding thin foam with the 
>> sandpaper to maintain pressure as the abrasive wears down. Today at 
>> the auto parts store they had sandpaper with grit as fine as 5000.
>>

>    What`s that equivalent to in microns ? I have diamond paste ... I 
> think "W 1" is one micron ? I was intending to use it to lap a loose 
> roller bearing outer race on a 1939 Harley transmission . It`s .0015" 
> out of round and that causes all kinds of grief .

   Clarification : I have several tubes of the diamond lapping paste 
with "W" numbers up to 40 .
-- 
Snag
  Men don`t protect women because they`re weak .
We protect them because they`re important .
 --- Mozilla/5.0 (Windows NT 6.1; WOW64; rv:60.0) Gecko/20100101
Thunderbird/60.6.1
 * Origin: A noiseless patient Spider (2:5075/128)
SEEN-BY: 5001/100 5005/49 5015/255 5019/40 5020/715
848 1042 4441 12000
SEEN-BY: 5030/49 1081 5058/104 5075/128
@PATH: 5075/128 5020/1042 4441



   GoldED+ VK   │                                                 │   09:55:30    
                                                                                
В этой области больше нет сообщений.

Остаться здесь
Перейти к списку сообщений
Перейти к списку эх