Nп/п : 1 из 100
От : FAQServer 2:5020/181 07 ноя 24 07:37:04
К : All 07 ноя 24 07:42:02
Тема : GEN86 - Два десктопа сменяют дpyг дpyга пpи пеpезагpyзке
----------------------------------------------------------------------------------
@MSGID: 2:5020/181 a037357b
@RFC-Message-ID: 1@mhm.com.lan>
@TZUTC: 0300
[Q]: Два десктопа сменяют дpyг дpyга пpи пеpезагpyзке
[A]: Unknown author
The problem with alternating Desktops is caused by a Drive being duplicated
in the File Handle Structure in the OS2SYS.INI file. In order to fixthis
problem, you must remove one of the duplicated Drive entries from the INI file.
Here is how you fix the problem with the alternating Desktops using UniMaint.
1. Make sure you have a Desktop Backup of your system. We are going to mess
with some things that could have a major effect on PM and WPS, so you always
want to have a place to go back to.
2. You are going to have to live with one Desktop or the other, so boot until
you get to the Desktop that you want and do the steps below immediately after
the Boot and do not do anything else until you are finished.
3. Bring up the main UniMaint window and use the File Menu to get the
System INI File as the file you are looking at. This is the OS2SYS.INI
file unless you have manually changed it.
4. Find PM_Workplace:Active Handles and highlight it. In the User Data Window
you will see with the Handles0 or the Handles1 Application Name.
5. Highlight the Application Name that is listed in the window. The Key
Names should not start with BLOCK1. There might be only on entry or there
could be a BLOCK2 etc. Don`t worry about how many there are.
6. Use the Find/Application Key Value to do a search on the drive that is
duplicated, D:, for example.
7. Looking at the information on the right hand side of the user Data Window,
when you find the entry you are looking for, you will see the characters
DRIV a few lines above the D: and the word NODE just past the D: that you
found. A few lines down you will find D: again. This is the good entry, so
you do not want to mess with it.
8. Use the Find/Repeat Last Find and it will find the second D: entry which
is the one above that is a few lines down from the first one.
9. Do the Repeat Find again and you should not be at the D: entry that is
the problem entry. Once again, you will see DRIV in front of the entry, NODE
just past it and another D: a few lines down.
10. You need to get rid of this D: drive, so you can move the cursor in the
User Data Window to the two D: entries and change the D to an invalid drive
by typing over it. You must change both of them, you must change them to
something that is a drive that does not exist and you must change both of
them to the same thing.
11. Go to the Action Menu and use Update Current Key to get the information
written to the OS2SYS.INI file.
12. This is probably not necessary, but I would suggest you now sit and wait
for at least one minute so that the modified OS2SYS.INI file is actually
written to you HD.
13. Now use the Desktop Menu, Reset Desktop to do a Reset of WPS. This will
cause WPS to collapse and all of your Icons will disappear. The Desktop
should come back in a minute or so. If the Desktop does not come back, then
do a three finger salute to reboot.
14. You should now have the Desktop you expect and the other Desktop will not
come back.
15. If you have the wrong Desktop, then you should use the Backup to Restore
the Desktop with the duplicate Handles and modify the other D: entry.
16. Once you have a good Desktop, then make a new Desktop Backup, so you can
always get back to where you are.
17. Finally, use the Recover menu, Repair INI Files to do the Default INI
File Repair. Just bring up the Dialog, click on Execute...this will fill
the Repair Window, select the Do Repair Button just above the data window and
click on Execute again. All of the problem entries will now be gone.
18. I would now make another Desktop Backup, do a Shutdown and Reboot just
to be sure that everything is okay.
19. After you have done a few Shutdowns and Reboots...over the space of a
couple of days or so. Then it would not hurt to make another Desktop Backup,
just to be sure that everything is okay.
It does not hurt to make several Desktop Backups, because the default is
to keep 10 generations. You should use the Description field to make careful
notes as to exactly where you are in the process above when you make each
Backup so that you will know exactly which generation to use if you need to
backtrack for any reason.
Let me know if you have any problems or do not understand any of the above.
If you get to a point in the procedure where you are not sure whether you are
in the right place and you have not made any changes, then stop right there
and ask questions. Once you have made any of the changes and written them to
the file, you must go all the way through the process or use the Desktop
Backup to Restore and start over.
--- INN 2.7.3 (20241006 prerelease)
* Origin: This echo is READ-ONLY. Send %HELP to FAQSERVER at (2:5020/181)
SEEN-BY: 4500/1 5001/100 5019/40 5020/77 81 101
181 545 848 1042 1941 1955
SEEN-BY: 5020/4441 8086 12000 5030/1081 1900
5060/900 5097/31 6090/1
@PATH: 5020/181 12000 4441